12V 460Ah Essential Series LiFePO4 Battery (5.89kWh)
Description
Heated Bluetooth RV lithium power
Epoch Essentials 12V 460Ah RV Lithium Battery | Heated & Bluetooth
A massive 5.89kWh single-battery powerhouse for RVs, camper vans, skoolies, and off-grid 12V systems.
The Epoch Essentials 460Ah is a 12V 460Ah RV lithium battery built for boondocking freedom, camper van battery upgrade projects, and high-capacity 12V power banks. This 12V 460Ah LiFePO4 battery stores 5.89kWh of energy in one Group 8D lithium replacement footprint, giving RVers, van builders, and off-grid travelers a powerful heated RV lithium battery with Bluetooth monitoring, 200A continuous discharge, internal heating, IP54 dust and splash resistance, and an 11-year limited warranty.
Built to go further
Maximum Power, Minimum Footprint
Replace a messy multi-battery lead-acid bank with one space-saving battery bank.
Van builders and RVers fight for every inch of storage and every pound of payload. The Epoch Essentials 12V 460Ah lithium battery consolidates high-capacity energy storage into one 84 lb package, helping eliminate unnecessary parallel wiring, reduce connection points, and free up valuable space in benches, under-bed electrical compartments, and RV battery bays.
With nominal energy roughly comparable to five standard 12V 100Ah lead-acid batteries—and far more usable capacity in real-world RV use—this high-capacity RV battery is ideal for simplifying a boondocking power setup without sacrificing runtime.
Built for Four-Season Boondocking
Automatic Internal Heating
Charging lithium cells below freezing can damage them, so the cells never take charge while any battery temperature reading is below 0°C (32°F). Instead, incoming solar, shore power, or DC-to-DC charge current (at least 0.5A from a connected charger) powers internal heating pads — never the battery's stored energy — and charging resumes automatically once the battery reaches 5°C (41°F). With heating, the charge temperature range is -20°C to 55°C (-4°F to 131°F); the heating system is tested to -20°C (-4°F) and rated for external ambient temperatures down to -40°C (-40°F).
IP54 Splash Resistance & Rugged Build
The IP54 enclosure is dust-protected and splash-resistant for standard RV battery boxes, storage bays, and high-vibration mobile environments. It is ideal for protected compartments, but it is not submersible and should not be pressure-washed or installed where standing water can collect.
Smart Power Management & Heavy Load Output
Run Heavy RV Loads with a 200A BMS
The 200A continuous Smart BMS allows this single battery to output roughly 2,560 watts at 12.8V before inverter losses. That makes it a strong match for properly designed 2,000W to 2,500W inverter systems powering microwaves, espresso machines, hair dryers, induction cooktops, and other common off-grid RV loads. The 400A peak discharge rating, for up to 10 seconds, helps handle short startup surges; size continuous loads, cables, and fuses to the 200A continuous rating.
Real-Time Bluetooth Monitoring via the Epoch Li-Ion App
The built-in Bluetooth RV battery monitor connects to the free Epoch Li-Ion app on iOS or Android so you can check state of charge, battery voltage, current draw, and temperature from the comfort of your camper bed—without installing a separate external shunt, because the shunt is built into the BMS (0.2A accuracy on discharge). The Bluetooth security PIN is printed on the battery's lid and can be changed in the app under Advanced Settings.
Essential Expandability & 11-Year Warranty
Build a bigger battery bank when your energy needs grow.
For extreme energy demands, up to 4 of these batteries can be wired in parallel for a massive 1,840Ah 12V battery bank, or up to 4 can be wired in series to create higher-voltage systems up to 48V. Use matched batteries and follow Epoch installation guidance for all series or parallel configurations.
The 4,000+ cycle life and 11-year limited manufacturer warranty make this battery a long-term investment for RVers, van builders, solar installers, and off-grid users who want reliable high-capacity lithium storage.
Best-fit RV and van applications
High-capacity 12V energy storage for boondocking and off-grid travel.
- ✓ Class A, Class B, and Class C RV house battery systems.
- ✓ Camper van battery upgrade projects and off-grid van conversion builds.
- ✓ Skoolies, truck campers, expedition rigs, and overland electrical systems.
- ✓ Boondocking power setup designs with solar, alternator charging, shore power, or inverter chargers.
- ✓ Large 12V inverter systems powering microwaves, induction cooktops, espresso machines, hair dryers, and other appliances.
- ✓ Marine and mobile house-power systems where IP54 splash resistance and 12V high-capacity storage are appropriate.
- ✓ Off-grid cabins, backup power, and solar storage systems using compatible LiFePO4 charging equipment.
- ✓ Group 8D lithium replacement applications where tray size, cable clearance, and charger profile match.
Battery features
High-capacity lithium power with cold-weather charging support and smart monitoring.
Compatible chargers and accessories
Recommended add-ons for a complete RV, camper, or van conversion installation.
Technical specifications & dimensions
Clean spec table for RV builders, van conversion planners, and solar installers.
| General | |
|---|---|
| Brand | Epoch Batteries |
| Model / SKU | 12460A-H |
| Product name | 12V 460Ah Essential Series LiFePO4 Battery |
| Series | Essential Series |
| Battery type | Heated Bluetooth deep-cycle LiFePO4 battery |
| Battery group size | BCI Group 8D |
| Chemistry | LiFePO4 / lithium iron phosphate |
| Cell type | Prismatic LiFePO4 |
| Cell configuration | 4S2P |
| Bluetooth | Yes — Epoch Li-Ion app (iOS and Android) |
| Bluetooth security PIN | Printed on the battery's lid; can be changed in the app (Advanced Settings) |
| Current sensing | BMS-integrated shunt; 0.2A accuracy on discharge |
| Internal heating | Yes — for cold-weather charging |
| Cycle life | 4,000+ cycles |
| Warranty | 11-year limited manufacturer warranty |
| Voltage and capacity | |
| Nominal voltage | 12.8V |
| Nominal capacity | 460Ah @ 0.2C |
| Energy stored | 5.89kWh / approx. 5,888Wh |
| Operating voltage range | 10.0V – 14.6V |
| Maximum charge voltage | 14.6V |
| Current ratings | |
| Max continuous discharge | 200A |
| Recommended discharge current | 138A (0.3C) |
| Max continuous charge current | 200A |
| Recommended charge current | 138A (0.3C) |
| Max discharge peak current | 400A for up to 10 seconds |
| Estimated continuous watt output | Approx. 2,560W at 12.8V × 200A, before inverter losses |
| Series and parallel configuration | |
| Series connections | Max 4 batteries in series, up to 48V |
| Parallel connections | Max 4 batteries in parallel |
| Maximum parallel bank capacity | Up to 1,840Ah with 4 matched batteries in parallel |
| Maximum configuration | 4S4P |
| Temperature | |
| Charge temperature range | -20°C to 55°C / -4°F to 131°F, with heating |
| Discharge temperature range | -20°C to 60°C / -4°F to 140°F |
| Recommended storage temperature | 0°C to 35°C / 32°F to 95°F |
| Low-temperature charge protection | Charging disabled at 0°C / 32°F; resumes automatically at 5°C / 41°F |
| Heater activation | Charger connected and supplying at least 0.5A; powered by incoming charge current only, never stored battery energy |
| Heating system | Tested to -20°C / -4°F; rated for external ambient down to -40°C / -40°F |
| Long-term storage | Charge to about 50% state of charge or higher; check at least every 3 months |
| Dimensions and weight | |
| Length | 20.55 in / approx. 52.20 cm |
| Width | 9.45 in / approx. 24.00 cm |
| Height | 8.60 in / approx. 21.84 cm |
| Overall dimensions | 20.55 in L × 9.45 in W × 8.60 in H |
| Weight | 84 lb / approx. 38.10 kg |
| Mechanical | |
| Case material | ABS and PC blend, UL94-V0 flame rating |
| Enclosure protection | IP54 — dust protected, splash resistant; not submersible |
| Terminal type | M8 female |
| Terminal torque | 8–12 N·m (71–106 in-lb) |
| Recommended charging settings | |
| Maximum continuous charge current | 200A (138A recommended) |
| Bulk / absorption voltage | 14.2V – 14.4V |
| Absorption end condition | Charge current ≤ C/20 (23A) or 15 minutes, whichever comes first |
| Float voltage | Disabled preferred, or 13.3V – 13.6V |
| Re-bulk voltage | 13.2V |
| Temperature compensation | 0mV/°C (off) |
| Equalization | Disabled |
| Charger temperature limit setting | 0°C to 55°C / 32°F to 131°F, unless the charger has approved cold-charge logic |
| BMS high-voltage cutoff | 14.6V |
| SoC recalibration | 14.6V |
| BMS protection | |
| Overcharge protection | Yes |
| Over-discharge protection | Yes |
| Over-current protection | Yes |
| Short-circuit protection | Yes |
| High and low temperature disconnects | Yes |
| Compliance | |
| Cell-level certifications | UL 1642; IEC 62619:2022 |
| Product | CE; RoHS |
| Transport | UN 38.3; Class 9 lithium battery shipping classification |
| Enclosure | IP54 per IEC 60529 |
IP54 splash-resistant protection
Dust protected, splash resistant, and built for protected mobile power compartments.
The IP54-rated enclosure is suitable for protected RV battery boxes, storage bays, under-bed installs, interior van electrical cabinets, and other mobile environments where splash resistance and dust protection matter. It should not be submerged or mounted where standing water can collect around the battery.
Why upgrade to Epoch LiFePO4?
More usable energy. Less wiring complexity. Longer service life.
LiFePO4 technology gives RVers and van builders stable voltage output, high usable capacity, fast charging, and maintenance-free operation. Compared with traditional lead-acid banks, this Epoch lithium battery offers cleaner wiring, less weight, and far more practical energy storage for extended boondocking and off-grid van conversion travel.
Fitment and charging note
Verify your compartment, inverter, charger, and wiring before installation.
Always confirm battery tray size, cable clearance, M8 terminal compatibility, fuse sizing, BMS current limits, inverter demand, charger profile, ventilation, and system grounding before installation. Use LiFePO4-compatible charging equipment programmed to Epoch’s recommended settings. For series or parallel battery banks, use matched batteries of the same model, age, capacity, and state of charge.
Epoch 12V 460Ah Essentials Battery FAQs
Answers for RV, camper, van conversion, solar, and boondocking power systems.
Can I replace a bank of multiple 100Ah batteries with this single 460Ah battery?
Absolutely. Replacing several smaller batteries with one Epoch Essentials 12V 460Ah battery can simplify wiring, reduce parallel connection points, free up storage space, and remove significant weight from an RV or van build. This single 84 lb battery stores approximately 5.89kWh of energy, making it a strong alternative to a large lead-acid bank.
What is the difference between the Essentials and Elite 460Ah batteries?
Both the Essentials and Elite 460Ah models offer large 5.89kWh-class capacity, Bluetooth monitoring, internal heating, and long warranty coverage. The Elite model is designed for more advanced installations with features such as IP67 waterproofing, higher continuous output, and Victron CANbus communication. The Essentials model is the cost-effective choice for RV, camper, and van builders who want a smart heated powerhouse without needing advanced Victron data integration.
What size inverter can I run with this 460Ah battery?
The Epoch 12V 460Ah Essentials battery has a 200A continuous discharge BMS. At 12.8V, that equals roughly 2,560W of continuous DC output before inverter losses. It is a strong match for properly sized 2,000W to 2,500W inverter systems and can power many common RV loads such as microwaves, coffee makers, induction cooktops, and hair dryers when the full system is designed correctly.
Will the internal heater drain my battery while I am off-grid?
No. The heater runs only while a connected charger supplies at least 0.5A, and it is powered by incoming charge current only, never the battery's stored energy, so it does not warm the battery while you are discharging it or while it is in storage. Below 0°C (32°F), charging pauses while the heating pads warm the battery, and charging resumes automatically at 5°C (41°F). It is not a space heater.
How do I check how much power I have left?
This battery includes built-in Bluetooth monitoring, so you can connect with the free Epoch Li-Ion app on a compatible iOS or Android device. The app shows state of charge, voltage, current, and temperature without a separate external shunt: a BMS-integrated shunt measures current with 0.2A accuracy on discharge. The Bluetooth security PIN is printed on the battery's lid; you can change it in the app under Advanced Settings.
Will this fit in my RV's battery compartment?
The Epoch 12V 460Ah Essentials battery measures 20.55 in L × 9.45 in W × 8.60 in H and weighs 84 lb. It is a BCI Group 8D battery, much larger than Group 24 or Group 27 batteries, so you should measure your battery tray, storage bay, under-bed compartment, or bench installation space before ordering.
Can I connect multiple 460Ah Essentials batteries together?
Yes. This model supports up to 4 batteries in parallel for a maximum bank capacity of 1,840Ah at 12V, and up to 4 batteries in series for higher-voltage systems up to 48V, to a maximum 4S4P configuration. Use matched batteries of the same model, age, capacity, and state of charge, and follow Epoch’s installation guidance.
Is this battery waterproof?
This Essentials model is rated IP54, which means it is dust-protected and splash-resistant for protected RV battery bays, storage compartments, and mobile environments. It is not designed for submersion. If you need full IP67 waterproofing, compare the Elite 460Ah model.
What charger settings should I use?
Use lithium-compatible charging equipment programmed for LiFePO4 batteries. Epoch lists 14.2V – 14.4V bulk/absorption ending at C/20 (23A) or after 15 minutes, whichever comes first; float disabled preferred or 13.3V – 13.6V; 13.2V re-bulk; equalization disabled; and temperature compensation off (0mV/°C). The recommended charge current is 138A (200A maximum continuous). For alternator charging, a DC-to-DC charger is highly recommended.
